[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 10 11 12 13 14 15 15 16 17 18 18 19 Reverse Door Swing Initial Start Up . Component Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance & Cleaning . Winterizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning Ice Making System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 21 22 23 23 24 Cube Size Control Bin Thermostat . [. . . ] Replace the door handle and filler plate; secure with screws previously removed. Hinge Filler Plate Parts Involved in Customizing Door Panel Custom Panel, Thin Panel Shown With Filler Hinge Door With Groove Door Handle August 1995 Page 10 WRF535SWBW AFTER INSTALLATION Reversing Door Swing: The hinged side of the door may be reversed to the other side if desired: The WRF535SWBW was shipped with the door hinged at the right. The door and hinges are designed for placing the hinges on either the right or the left side of the cabinet. Moving the hinges to the left allows the door to pivot from the left side. Note: There is a part, packed with the machine, that is required for this procedure. Open the door and remove the three screws holding the lower hinge to the cabinet. Hinge Filler Plate Door Handle 2. With the door open enough to see both screws at the top door hinge, remove the two screws. Remove the single screw and the hinge filler plate from the top of the door. Install the other filler plate (shipped inside refrigerator compartment) onto the top corner of the door where the hinge was. Remove the three plastic plugs from the top front corner where the hinge will mount. Remove the three plastic plugs from the lower front corner where that hinge will mount. Remove that hinge from the top and, flipping it upside down, install it onto the bottom of the door, on the opposite side using the original screws. A machine that has been emptied will usually take about 24-36 hours to re-fill. Harvest Control Knob Timer 5. Allow the unit to operate for 1 hour, and check the size of the cubes, if they are not correct, adjust as recommended on page 17. After the cubes are confirmed to be the correct size, replace all panels. Serial Number:___________________________ Date of initial start up:_____________________ 8. Fill out and mail the Warranty Registration. March 2006 Page 12 WRF535SWBW OPERATION How does the machine make ice? There are two distinct cycles: freeze and harvest. The Freeze cycle happens when water is sprayed against the freezing surface. The Harvest cycle is when the ice is released and water enters the machine. Freeze: During the freeze cycle the compressor is pumping refrigerant, the fan motor is blowing air, and the water pump is circulating water. As the refrigerated surface absorbs heat from the water sprayed against it, that heat is moved to the area where the fan is blowing air. The heat is transferred to the air, and the warmed up air is discharged from the ice machine. At the same time ice is forming on the refrigerated surface (located at the upper back of the machine). [. . . ] Add low side access valve, recover refrigerant, replace compressor and dryer, evacuate and weigh in the nameplate charge. Too much heat load. No water spray Cube size control will not close No airflow Not enough refrigerant Restricted system Hot gas valve leaks thru Compressor will not operate or pumps poorly. August 1995 Page 20 WRF535SWBW REPAIR Inlet Water Valve Electrical Shock Hazard Disconnect Electrical Power Before Beginning Removal of Parts The inlet water valve may need to be cleaned or replaced. If there is not enough water coming into the machine, the valve may need to be cleaned. If the valve does not work at all, or does not shut off tightly, it should be replaced. [. . . ]